? 2010 teledyne relays (800) 284-7007 ? www.teledynerelays.com shdc page 1 shdc\012010\q1 new series shdc output to 60a, 200 vdc high industrial performance (hippak) dc solid-state relays features/benefits ? latest generation mosfet technology ? ultra low on-state resistance ? low output leakage current ? built-in overvoltage protection ? reverse protected triggered control input to avoid linear control risks ? no radiated or conducted disturbances ? ip20 touch-proof fl aps ip20 touch-proof fl aps part number description SH10DC40 40a, 100 vdc solid-state relay SH10DC40-16 40a, 60 vdc solid-state relay sh20dc20-16 20a, 200 vdc solid-state relay sh20dc40-16 40a, 200 vdc solid-state relay sh75dc60-16 60a, 75 vdc solid-state relay part number explanation electrical specifications (+25c ambient temperature unless otherwise specifi ed) input (control) specifications min max units control range 3.5 32 vdc must turn-off voltage 1 vdc reverse voltage 32 vdc mechanical specification figure 1 figure 3 block diagram control + 3 |scst *included with -16 option mosfet phv driver C 4 output 1 + 2 C figure 2 control characteristic 50 45 40 35 30 25 20 15 10 5 0 0 @25c @100c @C35c control current (madc) control voltage (v) 2 4 6 8 10 12 14 16 18 20 22 24 26 28 30 3 2 1.77 (45) max 0.64 (16.3) 0.12 (3) 0.29 (30) max 2.30 (58.5) max 1.70 (43.2) 0.28 (7) 1.00 (25.4) m4 m5 2C 1+ 4/a2C 3/a1+ ?4.7 1.87 (47.6) dimensions in inches (mm) weight: 2.82 oz. (80g) 0.20(5.2) 1.10 (28) 10 line voltage 1 sh series dc switch type 2 40 output current C amps notes 1) line voltage (peak): 10 = 100 vdc 2) switch type: dc = dc 3) option: internal voltage protection -16 option 3
shdc page 2 specifications are subject to change without notice ? 2010 teledyne relays shdc\012010\q1 new series shdc output to 60a, 200 vdc high industrial performance (hippak) dc solid-state relays electrical specifications (+25c ambient temperature unless otherwise specifi ed) output (load) specifications min max units operating range SH10DC40 5 100 vdc SH10DC40-16 5 60 vdc sh20dc20-16 5 110 vdc sh20dc40-16 5 110 vdc sh75dc60-16 5 40 vdc peak voltage SH10DC40 100 vdc SH10DC40-16 100 vdc sh20dc20-16 200 vdc sh20dc40-16 200 vdc sh75dc60-16 75 vdc overvoltage protection (built-in) SH10DC40-16 56v (tvs) 1 sh20dcxx-16 75v (mov size 20) 2 sh75dc60-16 39v (tvs) 1 1) transient voltage supressor; 2) metal oxide varistor reverse voltage drop SH10DC40-16 1.3 v sh20dcxx-16 1.5 v sh75dc60-16 0.92 v nominal current (resistive) sh10 40 a sh20dc20-16 20 a sh20dc40-16 40 a sh75dc60-16 60 a non-repetitive peak overload current sh10 320 a sh20dc20-16 160 a sh20dc40-16 380 a sh75dc60-16 750 a leakage current 3 ma on-state resistance (@ 25 c) @25 c @125 c sh10 15 30 m sh20dc20-16 45 90 m sh20dc40-16 23 46 m sh75dc60-16 4.5 8.2 m electrical specifications (continued) (+25c ambient temperature unless otherwise specifi ed) output (load) specifications min max units output capacitance (typical) sh10 0.7 nf sh20dc20-16 0.6 nf sh20dc40-16 1.1 nf sh75dc60-16 1.5 nf junction-case thermal resistance sh10 0.9 c/w sh20dc20-16 1.2 c/w sh20dc40-16 0.7 c/w sh75dc60-16 1.2 c/w built-in heat sink thermal resistance (vertically mounted) 10 c/w heat sink thermal time constant 10 min control inputs/power outputs insulation voltage 2.5 kv turn-on time 20 s turn-on delay 20 s turn-off time 20 s turn-off delay 20 s on-off frequency 1000* hz *for high frequency, take two times the load current to calculate the heat sink. figure 4 time diagrams vc (control) tdon ton t t vt (switch) turn-on t t tdoff toff vc (control) vt (switch) turn-off
? 2010 teledyne relays (800) 284-7007 ? www.teledynerelays.com shdc page 3 shdc\012010\q1 new series shdc output to 60a, 200 vdc high industrial performance (hippak) dc solid-state relays built in overvoltage protection characteristics i elk : leakage current of relay i e : user load nominal current u tp : relay max. non repetitive peak voltage u tmax : max. nominal voltage of relay u to : possible overvoltage above u tmax u tn : user power supply voltage t : overvoltage duration t : time between 2 overvoltages figure 5a SH10DC40-16 figure 5b sh20dc20-16 & sh20dc40-16 figure 5c sh75dc-16 0 0 . 2 0 . 4 0 . 6 0 . 8 1 0 102030405060708090100 ut ( v ) utmax ( =uemax) utp i elk / i e 0 0 . 2 0 . 4 0 . 6 0 . 8 1 0 20 40 60 80 100 120 140 160 180 200 ut ( v ) utmax (=uemax) utp i elk / i e 0 0 . 2 0 . 4 0 . 6 0 . 8 1 0 5 1015202530354045505560657075 ut ( v ) utmax (=uemax) utp i elk / i e leakage current (a) voltage (vdc) leakage current (a) voltage (vdc) leakage current (a) voltage (vdc) utp uto < ie max) ut uto ( . max t ? = 75 0 1 1 ? ? = t t ie max) ut uto ( w p max ) protection (
shdc page 4 specifications are subject to change without notice ? 2010 teledyne relays shdc\012010\q1 new series shdc output to 60a, 200 vdc high industrial performance (hippak) dc solid-state relays general specifications (+25c ambient temperature unless otherwise specifi ed) environmental specifications min max units operating temperature C25 +90 c storage temperature C40 +100 c input-output isolation 2.5 kv insulation resistance 1 g insulation capacitance 8 pf junction temperature steady state 125 c transient 175 c case temperature 100 c connections power control screwdriver pozidriv2 tightening torque 2 n.m 1.2 n.m insulated crimp terminals (round tabs, eyelet type) m5 m4 miscellaneous display green led (on) housing ul94v0 mounting 2 screws (m4x12mm) noise level no audible noise general standards iec60947-1 protection level ip20 protection against direct touch yes ce marking yes e.m.c. emission radiated & conducted disturbances pending figure 6a high side wiring diagram (load connected to ) dc control power supply dc mains vc ic load ie ve vt c1 d2 on-off control (red paths as short as possible) 2C 1+ 4/a2C 3/a1+ figure 6b low side wiring diagram (load connected to +) dc control power supply dc mains vc ic load ie ve vt c1 d2 on-off control (red paths as short as possible) 2C 1+ 4/a2C 3/a1+ notes 1. for additional/custom options, contact factory. accessories faston: contact factory
? 2010 teledyne relays (800) 284-7007 ? www.teledynerelays.com shdc page 5 shdc\012010\q1 new series shdc output to 60a, 200 vdc high industrial performance (hippak) dc solid-state relays output relay characteristic curves for SH10DC40 & SH10DC40-16 0 5 10 15 20 25 30 -50 0 50 100 150 on resistance (m ) junction temperature ( c) figure 7c () 100 2 1 % ? 1 ? = t t d 0 40 80 120 160 200 240 280 320 360 0 . 1 1 10 100 1000 repetitive d=50% (tc=100c, tjmax=125c) non-repetitive d=1% (tc=100c, tjmax=175c) repetitive d=5% (tc=100c, tjmax=175c) repetitive d=10% (tc=100c, tjmax=175c) repetitive d=20% (tc=100c, tjmax=175c) pulse duration (s) on-state peak overload current (apk) figure 7b 0 5 10 15 20 25 30 35 40 45 0 102030405060708090100110 18.8 6.75 36.8 48 0 12 3 0.75 27 60.8 10 c /w 4 c /w 2.2 c /w 2.1 c /w 0.9 c /w 0.75 c /w 0.55 c /w 0.3 c /w 1.1 c /w 1.2 c /w ambient temperature ( c) load current (a) power dissipation (w) figure 7a
shdc page 6 specifications are subject to change without notice ? 2010 teledyne relays shdc\012010\q1 new series shdc output to 60a, 200 vdc high industrial performance (hippak) dc solid-state relays output relay characteristic curves for sh20dc20-16 0 20 40 60 80 100 120 -50 0 50 100 150 0 5 10 15 20 25 0 102030405060708090100110 20.25 9 36 0 2.25 56.25 10 c /w 4 c /w 2.2 c /w 2.1 c /w 1.1 c /w 0 . 9 c /w 0.55 c /w 0.3 c /w 1.2 c /w 0.75 c /w () 100 2 1 % ? 1 ? = t t d 0 20 40 60 80 100 120 140 160 180 0 . 1 1 10 100 1000 non-repetitive d=1% (tc=100c, tjmax=175c) repetitive d=50% (tc=100c, tjmax=125c) repetitive d=5% (tc=100c, tjmax=175c) repetitive d=10% (tc=100c, tjmax=175c) repetitive d=20% (tc=100c, tjmax=175c) on resistance (m ) junction temperature ( c) figure 8c pulse duration (s) on-state peak overload current (apk) figure 8b ambient temperature ( c) load current (a) power dissipation (w) figure 8a
? 2010 teledyne relays (800) 284-7007 ? www.teledynerelays.com shdc page 7 shdc\012010\q1 new series shdc output to 60a, 200 vdc high industrial performance (hippak) dc solid-state relays output relay characteristic curves for sh20dc40-16 0 10 20 30 40 50 60 -50 0 50 100 150 0 5 10 15 20 25 30 35 40 45 0 102030405060708090100110 30.2 10.9 59.2 77 . 3 0 19.3 4.8 1.2 43.5 97 . 8 8 c /w 4 c /w 2.2 c /w 2.1 c /w 0.9 c /w 0.75 c /w 0.55 c /w 0.3 c /w 1.1 c /w 1.2 c /w () 100 2 1 % ? 1 ? = t t d 0 40 80 120 160 200 240 280 320 0 . 1 1 10 100 1000 non-repetitive d=1% (tc=100c, tjmax=175c) repetitive d=5% (tc=100c, tjmax=175c) repetitive d=10% (tc=100c, tjmax=175c) repetitive d=20% (tc=100c, tjmax=175c) repetitive d=50% (tc=100c, tjmax=125c) on resistance (m ) junction temperature ( c) figure 9c pulse duration (s) on-state peak overload current (apk) figure 9b ambient temperature ( c) load current (a) power dissipation (w) figure 9a
shdc page 8 specifications are subject to change without notice ? 2010 teledyne relays shdc\012010\q1 new series shdc output to 60a, 200 vdc high industrial performance (hippak) dc solid-state relays output relay characteristic curves for sh75dc60-16 0 0 . 05 0 . 1 0 . 15 0 . 2 0 . 25 0 . 3 0 . 35 0 . 0001 0 . 001 0 . 01 0 . 11 d=50% d=20% d=10% d=5% d=2% d=1% single pulse 0 100 200 300 400 500 600 700 800 0 . 0001 0 . 001 0 . 01 0 . 11 non-repetitive d=1% (tc=100c, tjm ax=175c) repetitive d=50%(tc=100c, tjm ax=125c) repetitive d=5% (tc=100c, tjm ax=175c) repetitive d=10% (tc=100c, tjm ax=175c) repetitive d=20% (tc=100c, tjm ax=175c) 0 5 10 15 20 25 30 35 40 45 50 55 60 65 0 102030405060708090100110 0 0.21 10 c /w 4 c /w 2.2 c /w 2.1 c /w 1.1 c /w 0.9 c /w 0.55 c /w 0.3 c /w 1.2 c /w 0.82 1.85 3.3 5.15 7.42 10.1 13.2 16.7 20.6 24.9 29.7 34.8 0.75 c /w 0 . 1 1 10 100 1000 00,511,522,53 uc=0 ; tj=125c uc ? 0 ; tj=125c power element transient thermal impedance pulse duration (s) figure 10d pulse duration (s) on-state peak overload current (apk) figure 10b ambient temperature ( c) load current (a) power dissipation (w) figure 10a reverse voltage drop (v) reverse current (a) figure 10c 0 2 4 6 8 10 12 -50 0 50 100 150 on resistance (m ) junction temperature ( c) figure 10e
|
